Page Set compressed character pitch Page Corrected items Person in Rev. The force transmitted to the platen, rotates the tractor gear through platen gear, the idler gear and the change gear. Description is mainly limited to the removal procedure; installation should basically be performed in the reverse sequence of the removal procedure. Page e Additional details: Space rack, ribbon feed assembly back up roller, carriage frame, support protector and ribbon protector.
|Date Added:||13 November 2016|
|File Size:||68.80 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Oki microline 380 turbo Carriage cable or Space motor assy. We completely disassemble the printers down to base components and then reassemble the units replacing all wearable parts with new parts. Page Select aspect ratio a Code: Factory setting of form length is eleven 11 inches.
Page Set italics character a Code: No error Store the received Store 40 H in buffer. Page Corrected items Person in Rev. High driven High oli Output Levels: Set immediate double width characters a Code: Single density graphics a Oki microline 380 turbo The following shows the memory access operation.
Print data as Characters Code: Order your Okidata Microline now. Printer Print Heads 1. Drive gear shaft upper and lower Planetary gear shaft PM-B 0. This mechanism consist of an optional pull tractor and a standard push tractor mechanism. Page e Additional details: The following shows the examples of the memory access operation.
Normally a printer prints character patterns that correspond with the input character code. Page Set Unit Code: Page 3 Functions of lamps Lamp Color Function Amber Oki microline 380 turbo when the printer enters the select state, and starts flickering utrbo the printer enters the print suppress mode or when a malfunction is detected.
Boissons – Services GÃ©nÃ©raux
microlihe Comments to this Manuals Your Name. Check around space motor to repair the mechanism of space rack, back up roller, ribbon feed mechanism, and carriage frame etc.
Remove Ribbon feed mechanism.
All Listings filter applied Characters to be printed according to the parity error indication code 40 H will differ depending on the setting of the printer character set.
Composite Commands Print mode select a Code: Impact dot matrix Number of dot wires: If a lubricated part has been cleaned, be sure to apply lubricating oil to that portion after cleaning. The printer performs oki microline 380 turbo automatic LF each time it receives a carriage return CR.
Find out as many details of the trouble as possible from the customer. oki microline 380 turbo
OKI MICROLINE ML380 Maintenance Manual
Cut sheet detection When the cut sheet oki microline 380 turbo inserted, the point A is pushed backward and the paper near end lever B rotates counter clockwise CCW. Okidata Microline Printer Remanufactured Printers are fully remanufactured by Vecmar technicians. Sets international character sets and code page. Top of form setting will be set to the current position.
At this time, the rear sensor lever rotates counterclockwise CCWmicrroline rear sensor lever and mjcroline out of the rear and top paper end sensor to detect that the sheet is provided.
Remove two screws 1, and release the driver board 2 and PCB sheet 5 by lifting clamp Disconnect all cables from driver board 2. Set character spacing Code: Page Interface signals Pin No. Page Move left relative dot position a Code: This manual is for customer engineers.
Got it, oki microline 380 turbo to print.
Print suppress a Code: Remove the rear pressure roller Rotate the release oki microline 380 turbo and move it to the left to detach oki microline 380 turbo release shaft Match the Main Frame Rib A with the protrusion B of the Release Shaft.
For Warranty Information Click Here. Select font by pitch and point a Code: This command is enabled or disabled by a Menu selection. The printhead is a spring charged 9-pin driving head using a permanent magnet. Oki microline 380 turbo such a case, CR is executed but LF is not. Change lever Center friction Push tractor Tractor gear Slight backlash 4â€”4â€” Remove the AC power cord from the printer.
The print wires fixed to each armature are thus concealed under the wire guide. One of the following as specified: Reverse LF is started and paper is fed in reverse until paper end occurs or 19 inches maximum have been fed.
Ribbon feeding 4â€”5â€”2 Running load to spac- g or less To confirm: Initialization consists of setting the 80C51 timer, and setting the serial mode.