Press a corner of the sticky side of the label to the outer surface of the roll of ribbon. Maintenance Replacing the Printhead Skip to main content. Media Path Considerations Wipe the inside edges of both edge guides to remove any built-up residue. Discard the cleaning swabs after use – do not reuse.

Uploader: Arashicage
Date Added: 6 October 2014
File Size: 5.79 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 83040
Price: Free* [*Free Regsitration Required]

Close the printer and press the Feed button until a minimum of 4 inches or millimeters of zebra ztc gk420t labels exit the printer.

Media Path Considerations Wipe the inside edges of both edge guides to remove any built-up residue.

Clean from the middle to the zebra ztc gk420t. Push the right side printhead wire connector onto the printhead. The notches should have square corners.

About This Document Document Conventions Troubleshooting Tests, Printing A Configuration Label, Recalibration Recalibration Recalibrate the printer zebrz it starts to display unusual symptoms, such as skipping labels. Output Type see all Output Type.

The zebra ztc gk420t requires service. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. USB Cable Rev. Open the media roll holders.

Zebra default passwords

Press down zebra ztc gk420t the cover snaps closed. Refer to the one-flash sequence of Feed Button Modes on page 80 to print this label. If you discover shipping damage upon inspection: Item Location see all Item Location. Format see all Format. Use a small flat bladed screwdriver to remove the ribbon guide.


The KDU is strictly a terminal and zebra ztc gk420t not have the capability to store data or set up parameters. Our new search experience requires JavaScript to be enabled.


Did not leave a mark on the The ribbon is coated on the inside and can not be used in paper the G-Series printer. Page 25 The roll zebra ztc gk420t not sit in the bottom of the media compartment.

Pull the platen bearing latch release tabs on the right and left sides towards the front of the printer and rotate them up. Do Not Use ribbon cores with damaged notch. Brand see all Brand. Print Operations Print Meter Your Printer You must zebra ztc gk420t static-safe procedures when working with the printhead or the electronic components under zebrra top cover.

Gently but firmly pull the green ground wire off the printhead.

GK420t Desktop Printer Support

With continuous media, use the transmissive gap sensor so the printer can detect when the media runs out. Page 59 Printer Options Label Zebra ztc gk420t Option Lift zebra ztc gk420t liner over the top of the printer zebra ztc gk420t open the dispenser door. Connectivity see all Connectivity.

Please g4k20t JavaScript on your browserthen try again. The cabling and unique parameters for each of these physical printer communication interfaces is discussed in the following pages to assist you with making configuration setup choices prior to and immediately following applying power.

Related Articles  CANON IXY DV M5 DRIVERS

Windows Notepad text editor can be used to gi420t programing files. Install the zrbra in the printer. The Zebra series direct thermal printers also included Line Mode zebra ztc gk420t language support. Page 73 Adhesives and oils, for example, may be thinned by the initial cleaning but gk402t completely zebra ztc gk420t. Use a dry swab to remove any residue that may be left from the first cleaning.

The Printer Configuration Label, shown below, provides a listing of a majority of the configurations settings that can be set by ZPL command. If you have pre-loaded the driver suite with the Zebra Setup Utility, then the printer driver will automatically install. Page TrueType font to add glyphs characters.

Support Content Migration

A wide range of paper, polypropylene, polyester, and vinyl stock has been specifically engineered to enhance the printing capabilities of the printer and to prevent premature printhead zebra ztc gk420t.

Open the cover and dispenser door. Don’t show me this message again.